gess
Part of things
Posts: 220
|
|
May 27, 2024 18:11:34 GMT
|
I hope it was a bit of help at least. It was difficult to explain without pictures. If you register on the consul granada klubb norge Facebook page, you can see some information on the scanning and pre work on the louvres. It is not only for Norwegians. The guy Selling them copied the perana louvres, but not all the detail. Some metal tabs and fasteners will probably suffice. It is nice to be able ro remove it without damaging it. It is a rare piece.
|
|
|
|
|
gess
Part of things
Posts: 220
|
|
May 27, 2024 10:13:36 GMT
|
First of all, congrats on the louvers. In my opinion, the Granada needs it to complete the rear, especially on the sedan version. I have had a look at the Consul Granada Klubb Norge Facebook page. The guy selling these louvers is a member there. The raised bit on the bottom rung is for the Perana emblem, it was mounted with poprivets. So i guess you will have to make your own emblem and put on, cossiemonster emblem. :-) The installation should be with two tabs on the sides of the louvre. You stick a piese of plastic with a "keyhole" under the gasket an on the lovre there should be a keyhole aligning with the tab. The ypu insert the "key", rotate it 90 degrees and the luvre is locked in place. Your lovre is missing this feature. The original Perana lovre also had two bars running down the window inside the strengtheners you can see between the rungs. If these two bars were connected to something, I cannot see from the pictures.
On the sedan version, there are locing "keys" on the bottom corners, in addition there are two pieces of plastic holding it down at each side. the plastic bits are pressed in between te window and gasket. In addition there is a rod with a plastic fastener in each end. The plastic fasteners are pushed in between glass and gasket to hold the rod in place. On each end of the rod, one can thread the laouvre onto it to hold it in place.
I think you need to alter the lovre a bit to allow for some plastic bits to go between the glass and gasket to hold it in place in addition to some velcro. If you google Autoplas lovre fitting kit, you might find some hints.
|
|
|
|
gess
Part of things
Posts: 220
|
|
May 22, 2024 18:47:47 GMT
|
A guy inNorway re welded the C pillars with a tray and a drain at the lowest point. The sunroof cars has a drainhose leading into the C pillar adding to the water that comes in though the vents. He had a hose leading from the tray to, I think, through the spare wheel well.
|
|
|
|
gess
Part of things
Posts: 220
|
|
|
Impressive work, you really have a lot of rust to remove and a lot of bodywork to rectify. I have a similar work cut out for me sometime in the future. The wheelarch in the rear door opening has been repaired badly by previous owner, and I need to look into it at some time, but not now :-) The C pillars are always a problem, the way they are constructed with the inner metal only having a rubber gasket between the outer layer, it is a rust trap. I would strongly advice against welding up the vents on the C pillar. I did that on a Granada I had and it messed up the airflow in the coupe. I t would work kind of fine during normal conditions, but as soon as one window was wound down a bit, the car would pull exhaust through the boot into the coupe. Very annoying on warm summer days, and a bit risky with regards to CO2 an NOx getting into the car. You need some sort of ventilation in the rear.
Keep up the good work, it is an interresting project.
|
|
|
|
gess
Part of things
Posts: 220
|
|
|
|
|
|
|
gess
Part of things
Posts: 220
|
|
May 10, 2023 13:35:13 GMT
|
|
|
|
|
gess
Part of things
Posts: 220
|
|
|
A guy in Norway, an engine tuner, did a project on one of these Micras a long time ago. He methodically tested and tuned the car, checking the progress with multipe runs on a dyno. He started with the basics, oil change, filters, plugs and leads. Basic maintenance actually. he got quite a lot of the lost ponies back that way. He then got into the aspiration, putting a spacer on the intake to make the distance from the "carburettor" to the cylinder longer, upgrading the air delivery system and also upgraded the exhaust manifold. I don't remember the figures, but he got a fair bit above the original horsepower number without messing with electronics and the internals of the engine.
|
|
|
|
gess
Part of things
Posts: 220
|
|
|
Sorry to read about your diabetes, it is unfortunate, but still it is good to get a dignosis so that you can get some treatment. I know several people who are diabetics, and they live well. Is it type 1 or 2? You don't have to reply.
I think you should think of this card and the funds as what it is. A token of gratitude/payment for the interresting and entertaining thread you have kept going since 2012. Put the money in ypur project as it was intended and keep the project alive :-)
|
|
|
|
gess
Part of things
Posts: 220
|
|
Feb 10, 2023 11:59:22 GMT
|
I know that a guy in Norway changed his Granada diff for a Sierra unit, similar to the one you have bought. He made a sort of frame that was bolted or welded to the rear subframe. I think he used a modified Sierra rear diff bush instead of the large Granada bush, and moved the point where it bolts to the chassis. He elongated the propshaft to suit the new flange location on the new diff. It requires a bit of welding and a lot of measurements, but could be an option instead of welding the sleeve to a flange.
|
|
|
|
gess
Part of things
Posts: 220
|
|
Jan 13, 2023 10:51:51 GMT
|
Hi Alex. I have been watching your loom rebuild, what an amazing job you did there. The attention to detail, sourcing all types of connectors and pins, making Excel spreadsheet etc. I am in awe! I am struggeling to find time to do the most necessary work on my daily, in additiont to family life. How you find the time is beyond me. Not to mention the mojo. I had great plans for this fall, but didn't even get off the starting block. Sorry to read that you have issues after doing such t thorough job of identifying all of the wires and sensors. If I understand it correctly, the engine is running on the cylinders, all on one side. Checking if it is fuel or spark related would be my first port of call. If it is fuel related, I would try to assess if it is the injectors, fuelpipe or loom that is causing the problem. Money is on the loom. If it is spark related, I would check plugs, plug leads and of course the coil. Is it possible to switch over the coil side to see if the other side fires up? I really don't know these engines and I assume you already have a plan for going forward. Best of luck. I will be watching in anticipation.
|
|
|
|
gess
Part of things
Posts: 220
|
|
Sept 27, 2022 6:28:31 GMT
|
Impressive work on the wiring system. You really have got a stamina worth admiring. The effort and dedication is impressive! I do believe that you will make it work properly and safe. The state the engine loom was in terrified me. All that cracked insulation and green copper was a disaster waiting to happen. It will take some time but the end result will be way better than it was. Keep up the good work, we are cheering you on!
|
|
|
|
gess
Part of things
Posts: 220
|
|
Sept 19, 2022 5:08:28 GMT
|
That tracor is coming along great. You really have a lot to do on the farm. In Norway they had a show about one of these grey tractors, Gråtass.
|
|
|
|
gess
Part of things
Posts: 220
|
|
|
That Emu is looking good. Have you got any sockets left after this creation is done?
|
|
|
|
gess
Part of things
Posts: 220
|
|
|
That was just perfect!
|
|
|
|
gess
Part of things
Posts: 220
|
|
Jun 17, 2022 11:08:03 GMT
|
WOW, this is awesome in so many ways. Are there any rules for firewall between area with fuel cell and cockpit? I see you have installed aftermarket electric windows, what brand is it? Loving how you have retained the comfort, good seats, nice carpets and electric windows in this bonkers car.
|
|
|
|
gess
Part of things
Posts: 220
|
|
Jun 17, 2022 10:39:57 GMT
|
First of all, it is a good thing that you are getting your money back and that you are in a good place! Really sad to see the car dismantled and stripped. It was such a cool project. All your faffing about, the ups and downs have been very entertaining to read about. I don't like that you are unlucky and things blow up, but you make it into very interesting reading. I will have a look at your new project, and cross my fingers that it goes well.
|
|
|
|
gess
Part of things
Posts: 220
|
|
Jun 14, 2022 10:19:10 GMT
|
Really sorry to read about your near miss. But the silver lining is that it is a near miss and not a total catastrophe. It could have been so much worse, at least your car is in a coma needing a new brain, not a total rebuild. I hope you will be able to find the cause of this mishap so that you can avoid it in the future. I guess that sourcing the needed parts will take some time, but I am confident you will get there in the end. Could it be an option to install a simpler engine to get you through the summer? A carburetted V6 with a normal C3 box, or are they difficult to find and expensive?
|
|
|
|
gess
Part of things
Posts: 220
|
|
Apr 13, 2022 10:44:06 GMT
|
I would recommend a Defa system in your car. As a Scandinavian I know how much it improves the daily commute, to start a warm engine, and place my rear end on a seat which is not freezing cold is preferable to the opposite. I installed both the block heater, wiring harness and coupe heater myself. It is quite easy on most models. you can get it for 120V also. Some heaters plug into the block, and some are installed on a hose, either way, it heats the cooling fluid which cirkulates heating the entire engine and oil. A coupe heater will add cost but also increase comfort. www.defa.com/content/uploads/Documentation/WarmUp/Marketing-Materials/DEFA-North-American-Brochure_English_2018-19.pdf?timestamp=1649846157
|
|
|
|
gess
Part of things
Posts: 220
|
|
Mar 30, 2022 18:57:30 GMT
|
This is really a big bummer. I have enjoyed this thread, and finally the car was in working order, but then not. I undersatand that you lost the mojo with this car, it has been fighting you a lot. I guess you summed it up pretty good, the magic is gone. I was hoping there was a but at the end and that you would dig deep and rebuild but I guess this is it. It has been an epic journey, an interresting and entertaining thread. I always looked forwards to your updates, so I guess this sort of is the end of an era. I really hope you get some money back from this one and that you find some other car that yoy and your kids can enjoy.
Best of luck with your next project!
|
|
|
|
gess
Part of things
Posts: 220
|
|
|
That workbench is really looking smart. It seems very practical, at least for clean woodshop work, maybe not so much for dirty engine and gearbox work. How stable is it when you fold up the table? I would assume it could fall over if you put too much weight on the unsupported side. nice to read thqt the Granada is performing as it should. That bodes well for the new 2022 season!
|
|
|
|