|
|
|
Dec 23, 2008 21:25:54 GMT
|
|
Hi guys, Any one know what sort of angle blackbird bike carbs would need to be angled at to get the floats working correctly?
|
| |
1987 Mini with Suzuki Swift GTI engine
2005 BMW E91 320D Touring
|
|
|
|
|
|
|
Dec 23, 2008 22:13:57 GMT
|
bogg brothers that make the manifolds for bike carbs would k now www.boggbros.com o think |
| |
2001 HONDA CT110 (NOT RCV)
|
|
|
|
|
Dec 23, 2008 22:18:29 GMT
|
 that would be fairly upright then |
| |
2001 HONDA CT110 (NOT RCV)
|
|
|
|
|
Dec 23, 2008 22:34:15 GMT
|
|
i've got a spare set of bike carbs if anyone wants em, i think they're from a kwaka of some sort, maybe a 400 or 600 so i don't know if they're big enough for a car
|
| |
69 Plymouth Fury Convertible 75 Range Rover 2 door 82 Range Rover 4 door
84 Range Rover 4 door 78 Datsun 120Y 2 door 78 Datsun 120Y Coupe
78 Datsun 620 Pickup 81 Datsun Urvan E23 86 Datsun Vanette van
98 Electric Citroen Berlingo 00 Electric Peugeot Partner 02 Electric Citroen Berlingo 76 Honda C50
04 Berlingo Multispace petrol 07 Land Rover 130 15 Nissan E-NV200 15 Fiat Ducato
|
|
|
|
|
Dec 24, 2008 10:49:09 GMT
|
|
What's the throttle size on them?
|
| |
1987 Mini with Suzuki Swift GTI engine
2005 BMW E91 320D Touring
|
|
|
|
|
Dec 24, 2008 11:53:20 GMT
|
|
|
| |
|
|
|
|
|
Dec 24, 2008 21:45:59 GMT
|
|
very very upright.... Ermm I wonder how important the angle is.
I'm running the engine on mega jolts with a map sensor. If I link both tracks together and use a small chamber to even out the vacum and feed that to the mj unit, will that do the job?
Thanks
|
| |
1987 Mini with Suzuki Swift GTI engine
2005 BMW E91 320D Touring
|
|
v6pop
Part of things
Posts: 110
|
|
Dec 24, 2008 21:58:22 GMT
|
Make sure the angle is as close to original as possible,to far out will cause fueling problems(incorrect amount of fuel for float hieghts/flooding) Good air box with filter helps bottom end response too. Good luck  |
| |
|
|
|
|
|
Dec 25, 2008 16:59:36 GMT
|
|
black bird carbs run a pretty steep angle so you should be ok
|
| |
|
|
|
|
|
Dec 28, 2008 10:57:14 GMT
|
|
|
| |
Diehard wheel geek
|
|
starchild
Part of things
suck/squeeze/bang/blow.
Posts: 66
|
|
Dec 28, 2008 17:10:13 GMT
|
very very upright.... Ermm I wonder how important the angle is. I'm running the engine on mega jolts with a map sensor. If I link both tracks together and use a small chamber to even out the vacum and feed that to the mj unit, will that do the job? Thanks a mate of mine has fzr 600 carbs on a zetec engine running mega jolt and he made a chamber as you suggest he made his from a piece of stainless exhaust pipe welded at the ends works perfect. |
| |
|
|
|
|
|
Dec 28, 2008 18:36:59 GMT
|
|
hi measured the ones i have, they are 30mm measured at the butterflies
|
| |
69 Plymouth Fury Convertible 75 Range Rover 2 door 82 Range Rover 4 door
84 Range Rover 4 door 78 Datsun 120Y 2 door 78 Datsun 120Y Coupe
78 Datsun 620 Pickup 81 Datsun Urvan E23 86 Datsun Vanette van
98 Electric Citroen Berlingo 00 Electric Peugeot Partner 02 Electric Citroen Berlingo 76 Honda C50
04 Berlingo Multispace petrol 07 Land Rover 130 15 Nissan E-NV200 15 Fiat Ducato
|
|
ezpez
Part of things
Posts: 183
|
|
Dec 28, 2008 20:32:56 GMT
|
|
if there only 30mm i wouldnt think they would be much use on a car engine tbh cause my 125 runs off a 28mm. prolly off a 400, i cant think of a 4 pot with a smaller capacity.
|
| |
|
|
|
|
|
Dec 30, 2008 21:54:36 GMT
|
|
looking for some 40mm + sized carbs.
thanks
|
| |
1987 Mini with Suzuki Swift GTI engine
2005 BMW E91 320D Touring
|
|
