1964 Ford Ranchero
347ci small-block Ford by ATK High Performance Engines
413hp 434ft.lbs torque
QFT 680cfm carb
Scat nodular iron 3.4" stroker crank
Scat 4340 Forged I-beam 5.4" rods
Icon forged FHR pistons with moly rings
10.2:1 compression
Hydraulic roller cam 220/224@0.050 .512in/.512ex 112 LSA
Edelbrock Performer RPM heads 60cc/170cc 2.02/1.60 in/ex valves
Billet 1.6 full roller rockers
MSD Blaster 2 coil
MSD Ready-To-Run distributor
Mishimotu aluminium radiator
Dougs Tri-Y headers
Custom stainless 2.5" exhaust system with X pipe
Transmission:
Performance Automatics C4 transmission with manual reverse pattern valve body (no brake)
B&M Quicksilver ratchet shifter
Edge 9" 2400 stall converter, clutch eliminator with aluminium stator, tig welded pins in turbine and is spragless.
Chassis and suspension:
Chris Alston Chassis Works bolt in front coil-overs
1" Anti-roll bar
Stoptech drilled and vented front disks
Manual steering conversion (hate the leaky Ford assist rams)
Subframe connectors
Baer bump steer correction kit
Ford 8" axle with Eaton True-trac diff and new bearings by Hauser
Moser 28-spine half shafts
Prop loop
Calvert Racing Rancho adjustable drag shocks
Cal-trac traction bars
Fibreglass front bumper, needs a fresh coat of satin black (have the original steel one too)
15" Cragar Black D Window wheels with NHT Galaxy's all round
I've just spent £700 down the body shop welding up the right outer rear quarter, and the left inner rear arch as they were starting to go. The other rear quarter will need some attention. There are a few spots appearing around it but then it is a 55 year old truck, structurally its all solid. Engine, transmission and rear end are all dry, no leaks. Freshly Waxoyled underneath after the body work.
The speedo doesn't work but the other gauges do, inc fuel!
Over the last year or two its had a new alternator, starter motor, fuel pump and its just had 2 new front wheels and tires. Dependent on the deal I've got a pair of fresh rear wheels with Mickey Thompson drag radials mounted to go with it too.
This is by no means a clean shiny show truck but is a very usable go anywhere VERY quick bit of kit, I've been 12.46@107mph in it and have previously used it as a daily. Spend a bit of time sorting the cosmetics out, or just enjoy is as it is!
Open to a decent bit of cash my way P/X's.....
347ci small-block Ford by ATK High Performance Engines
413hp 434ft.lbs torque
QFT 680cfm carb
Scat nodular iron 3.4" stroker crank
Scat 4340 Forged I-beam 5.4" rods
Icon forged FHR pistons with moly rings
10.2:1 compression
Hydraulic roller cam 220/224@0.050 .512in/.512ex 112 LSA
Edelbrock Performer RPM heads 60cc/170cc 2.02/1.60 in/ex valves
Billet 1.6 full roller rockers
MSD Blaster 2 coil
MSD Ready-To-Run distributor
Mishimotu aluminium radiator
Dougs Tri-Y headers
Custom stainless 2.5" exhaust system with X pipe
Transmission:
Performance Automatics C4 transmission with manual reverse pattern valve body (no brake)
B&M Quicksilver ratchet shifter
Edge 9" 2400 stall converter, clutch eliminator with aluminium stator, tig welded pins in turbine and is spragless.
Chassis and suspension:
Chris Alston Chassis Works bolt in front coil-overs
1" Anti-roll bar
Stoptech drilled and vented front disks
Manual steering conversion (hate the leaky Ford assist rams)
Subframe connectors
Baer bump steer correction kit
Ford 8" axle with Eaton True-trac diff and new bearings by Hauser
Moser 28-spine half shafts
Prop loop
Calvert Racing Rancho adjustable drag shocks
Cal-trac traction bars
Fibreglass front bumper, needs a fresh coat of satin black (have the original steel one too)
15" Cragar Black D Window wheels with NHT Galaxy's all round
I've just spent £700 down the body shop welding up the right outer rear quarter, and the left inner rear arch as they were starting to go. The other rear quarter will need some attention. There are a few spots appearing around it but then it is a 55 year old truck, structurally its all solid. Engine, transmission and rear end are all dry, no leaks. Freshly Waxoyled underneath after the body work.
The speedo doesn't work but the other gauges do, inc fuel!
Over the last year or two its had a new alternator, starter motor, fuel pump and its just had 2 new front wheels and tires. Dependent on the deal I've got a pair of fresh rear wheels with Mickey Thompson drag radials mounted to go with it too.
This is by no means a clean shiny show truck but is a very usable go anywhere VERY quick bit of kit, I've been 12.46@107mph in it and have previously used it as a daily. Spend a bit of time sorting the cosmetics out, or just enjoy is as it is!
Open to a decent bit of cash my way P/X's.....