|
|
Jul 24, 2017 13:05:26 GMT
|
For Sale! I have four, 15", rather rare, MIM Stinnes alloy wheels. These were custom ordered to fit a TVR 350i which run Mk2 Granada hubs (5x112). The wheels are 7J wide with an et35 offset. I bought these from a chap who'd gone to great expense ordering and customising these wheels. Whilst they look like split rims, they are in fact one piece rims. He had an engineering company machine the rims to accept Allen head bolts around the rim - which I think, looks rather good! He then sold his TVR Tasmin before ever fitting the wheels. I bought them from him and ran them on my TVR 350i for a few years. I'm now going back to the factory fit lattice alloys, so these are surplus to requirments. The good: No cracks, no scuffs, no damage. All center caps are present as are the retaining bolts. These wheels have maybe only done 10,000 miles in total The bad: As you can see in the picture, water has got under the lacquer on the wheel rim and caused some 'worming'. On one rim the lacquer has worn off completely and the aluminium has oxidised black. Essentially, a good weekend with a polishing mop and some cutting compound, and I reckon you'd be good to go. Asking £185 or best offer. May be able to deliver to Retro Rides Gathering. Wheels are located in Ravenshead Notts, just off Junction 27 of the M1
|
|
|
|
|
|
Jul 24, 2017 13:06:21 GMT
|
|
|
|
|
mk2cossie
Club Retro Rides Member
Posts: 2,937
Club RR Member Number: 77
|
|
Jul 24, 2017 13:28:53 GMT
|
Seriously tempted by these misterbob! And I could say they are a birthday present to myself in a few weeks What is the inner rim profile of these tho? As they may not fit over my front brakes
|
|
|
|
|
|
Jul 24, 2017 18:01:49 GMT
|
Seriously tempted by these misterbob! And I could say they are a birthday present to myself in a few weeks What is the inner rim profile of these tho? As they may not fit over my front brakes Hello mate! What do you need to know exactly? Inner rim diameter? I can go and measure anything you want, just let me know
|
|
|
|
mk2cossie
Club Retro Rides Member
Posts: 2,937
Club RR Member Number: 77
|
|
Jul 25, 2017 12:35:47 GMT
|
Well, its the fact I have 316mm discs and 4pot calipers on the granny. So ideally the inner rim profile and diameter possibly would help
|
|
|
|
|
|
Jul 25, 2017 12:53:01 GMT
|
Well, its the fact I have 316mm discs and 4pot calipers on the granny. So ideally the inner rim profile and diameter possibly would help Cool, I'll get you some measurements.
|
|
|
|
|
|
|
Well, its the fact I have 316mm discs and 4pot calipers on the granny. So ideally the inner rim profile and diameter possibly would help Right, you may be in luck! Measured the rims on Friday. The narrowest measurement, at the hub face, was 330mm widening out to 365mm.
|
|
|
|
mk2cossie
Club Retro Rides Member
Posts: 2,937
Club RR Member Number: 77
|
|
|
Thanks for that misterbob Shall try and measure up my inner dimensions and caliper size one night this week, or the weekend most likely. If thats ok for you?
|
|
|
|
|
|
|
Thanks for that misterbob Shall try and measure up my inner dimensions and caliper size one night this week, or the weekend most likely. If thats ok for you? If you can let me know before the weekend, that'd be great
|
|
|
|
mk2cossie
Club Retro Rides Member
Posts: 2,937
Club RR Member Number: 77
|
|
Aug 12, 2017 16:21:43 GMT
|
Sorry for not getting round to this sooner misterbob. Been busy all week or rained off from looking at the clearances. I shall have to pass I'm afraid, as the narrowest part on my 16inch wheels is 355mm going out to about 380mm, with a very close caliper
|
|
|
|